• Form Factor	Stand/Boom Mount
  Sound Field	Mono
  Operating Principle	Line Gradient
  Capsule	Condenser
  Diaphragm	0.5″ / 12.70 mm
  Polar Pattern	Supercardioid
  Orientation	End Address
  Circuitry	Solid-State (JFET)
  Pad	None
  High-Pass Filter	80 Hz, 12 dB/Octave
  Tone Adjustment	None
  Gain Adjustment	None
  Indicators	None
  On-Board Controls	High-Pass Filter
  Windscreen	Foam (Included)

  Performance

  Frequency Range	20 Hz to 20 kHz
  Maximum SPL	131 dB SPL (1 kHz, 1% THD, 1-Kilohm Load)
  Off-Axis Rejection	14 dB at 60° 16 dB at 120° 12 dB at 180°
  Impedance	250 Ohms (Phantom Power) 350 Ohms (Battery Power)
  Sensitivity	-36 dBV/Pa at 1 kHz
  Output Level	6.9 mV (Max)
  Dynamic Range	113 dB
  Signal-to-Noise Ratio	76 dB A-Weighted (1 kHz)
  Equivalent Noise Level	18 dB A-Weighted

  Connectivity

  Output Connectors (Analog)	1 x XLR 3-Pin
  Headphone Connector	None

  Power

  Operating Voltage	48 V (Phantom Power) 1.5 V (Battery Power)
  Operating Current Consumption	2 mA (Phantom Power) 0.18 mA (Battery Power)
  Battery Type	1 x AA (Not Included)

Sound Blankets with Grommets can be used to blackout a window or hang in a room when added sound insulation is needed. Sound Blankets can also be used to protect equipment during transportation.

PN 329040-1: Sound Blanket
Weight: 5.25lbs

RODE VIDEOMIC PRO R – COMPACT DIRECTIONAL ON-CAMERA MICROPHONE WITH RYCOTE SHOCKMOUNT

• Rycote® Lyre® shock mounting onboard
• All-new capsule with lower noise and higher sensitivity
• Broadcast recording quality condenser microphone
• Compact form factor (150mm/6” length)
• Ultra lightweight (85g/3oz)
• 9V battery powered – over 70 hours use (alkaline)
• Integrated shock mounting
• Integrated foam windscreen
• 3.5mm stereo mini-jack output (dual mono)
• Two step High Pass Filter (flat, 80Hz)
• Three position level control (-10dB, 0, +20dB)
• Camera shoe mount with 3/8” thread for easy boompole mounting

The RODE VideoMic Pro is a true shotgun microphone designed for use with camcorders, DSLR cameras and portable audio recorders as a source of primary and reference audio.

At the heart of the VideoMic Pro is an all-new 1/2″ condenser capsule that provides broadcast-quality audio via a 3.5mm minijack connector (outputting the mono signal to both left and right channels) with an incredibly low self-noise of just 14db. A super-cardioid polar pattern ensures that surrounding audio is minimised, and your recording is focused on the subject in front of the camera.

The integrated Rycote® Lyre® based shock mounting system separates the VideoMic Pro capsule and electronics from its mount, providing isolation from external physical factors that may cause unwanted rumble and vibrations in the microphone. Constructed from a single piece of hard-wearing thermoplastic, the Lyre® provides superior acoustic suspension to traditional elastic solutions, and will never wear out, sag or snap.

Easily accessible on the rear face of the microphone are the power, filter and level controls. In addition to the microphone’s native 40Hz-20kHz response a selectable high-pass filter at 80Hz is available, which will prevent low end noise such as air conditioners and traffic from being recorded.

Below these controls are the level settings, which attenuate or boost the recorded level as required. The -10dB level attenuation (or PAD) is ideal for recording loud sound sources, such as live music, motorsport, or interviews where the subject is very close to the camera. The +20dB level boost is designed for use with DSLR cameras, allowing the user to reduce the camera’s preamp level (or mic-input level), effectively reducing the amount of noise generated by the camera’s comparatively low quality audio circuitry.

The microphone uses a standard sized shoe mount for on camera use, and features a 3/8″ thread in the base of the mount for easy boom pole mounting.

The VideoMic pro is battery powered, and provides over 70 hours recording from a single 9V battery.

The RODE VideoMic is designed and made in Australia, and covered by RODE Microphones’ industry leading 10 year warranty.

• dimensions

  diameter 20 mm, length 256 mm

• Microphone

  super-cardioid/lobar

• Frequency response

  40 Hz to 20 kHz

• Max. sound pressure level

  132 dB SPL at P48; 126 dB SPL with battery powering

• Weight

  128 g (without battery)

• Sensitivity in free field, no load (1kHz)

  21 mV/Pa at P48; 19mV/Pa with battery powering

• Equivalent noise level

  15 dB (A) at P48; 16 dB (A) with battery powering

• Operating time

  approx. 150 hrs

• Power supply

  48 V +/- 4V (P48, IEC 61938) or battery/rechargeable batt. 1,5V/1,2V AA size

• Current consumption

  4,4 mA at P48